0

ATV71HU22Y

SKU:ATV71HU22Y

Price upon request

  • Product is not available

-
+
Send Enquiry

Minimum Order Quantity1

Accept Small Orders No

Variable speed drive ATV71 - 2.2kW - 690V - EMC filter-graphic terminal
Add to Wishlist Remove Wishlist Add to Compare

  • Additional Information

    Main
    range of product
    Altivar 71
    		  
    product or component type
    Variable speed drive
    		  
    product specific application
    Complex, high-power machines
    		  
    component name
    ATV71
    		  
    motor power kW
    1.5 kW, 3 phases at 500 V
    2.2 kW, 3 phases at 690 V
    		  
    motor power hp
    2 hp, 3 phases at 575 V
    		  
    maximum motor cable length
    10 m shielded cable
    10 m unshielded cable
    		  
    power supply voltage
    500...690 V - 15...10 %
    		  
    network number of phases
    3 phases
    		  
    line current
    3.2 A for 600 V 3 phases / 2 hp
    3.8 A for 500 V 3 phases 1.5 kW
    4 A for 690 V 3 phases 2.2 kW
    		  
    EMC filter
    Integrated
    		  
    assembly style
    With heat sink
    		  
    variant
    Reinforced version
    		  
    prospective line Isc
    22 kA for 3 phases
    		  
    nominal output current
    2.7 A at 4 kHz 575 V 3 phases / 2 hp
    3.2 A at 4 kHz 500 V 3 phases 1.5 kW
    4 A at 4 kHz 690 V 3 phases 2.2 kW
    		  
    maximum transient current
    4.8 A for 60 s 3 phases 1.5 kW
    5.28 A for 2 s 3 phases / 2 hp
    5.28 A for 2 s 3 phases 2.2 kW
    		  
    output frequency
    0.1…500 Hz
    		  
    nominal switching frequency
    4 kHz
    		  
    switching frequency
    2.5...6 kHz adjustable
    4...6 kHz with derating factor
    		  
    asynchronous motor control profile
    Voltage/frequency ratio (2 or 5 points)
    Sensorless flux vector control (SFVC) (voltage or current vector)
    Flux vector control (FVC) with sensor (current vector)
    ENA (Energy adaptation) system for unbalanced loads
    		  
    type of polarization
    No impedance for Modbus
    		  
    Complementary
    product destination
    Asynchronous motors
    Synchronous motors
    		  
    power supply voltage limits
    425…759 V
    		  
    power supply frequency
    50...60 Hz - 5...5 %
    		  
    power supply frequency limits
    47.5...63 Hz
    		  
    speed range
    1…100 for asynchronous motor in open-loop mode, without speed feedback
    1…1000 for asynchronous motor in closed-loop mode with encoder feedback
    1…50 for synchronous motor in open-loop mode, without speed feedback
    		  
    speed accuracy
    +/- 0.01 % of nominal speed in closed-loop mode with encoder feedback 0.2 Tn to Tn
    +/- 10 % of nominal slip without speed feedback 0.2 Tn to Tn
    		  
    torque accuracy
    +/- 15 % in open-loop mode, without speed feedback
    +/- 5 % in closed-loop mode with encoder feedback
    		  
    transient overtorque
    170 % of nominal motor torque +/- 10 % for 60 s every 10 minutes
    220 % of nominal motor torque +/- 10 % for 2 s
    		  
    braking torque
    <= 150 % with braking or hoist resistor
    30 % without braking resistor
    		  
    synchronous motor control profile
    Vector control without speed feedback
    		  
    regulation loop
    Adjustable PI regulator
    		  
    motor slip compensation
    Adjustable
    Suppressable
    Automatic whatever the load
    Not available in voltage/frequency ratio (2 or 5 points)
    		  
    diagnostic
    1 LED (red)drive voltage:
    		  
    output voltage
    <= power supply voltage
    		  
    insulation
    Electrical between power and control
    		  
    type of cable for mounting in an enclosure
    With a NEMA Type1 kit: 3 wire(s)UL 508 cable at 40 °C, copper 75 °C / PVC
    With an IP21 or an IP31 kit: 3 wire(s)IEC cable at 40 °C, copper 70 °C / PVC
    Without mounting kit: 1 wire(s)IEC cable at 45 °C, copper 70 °C / PVC
    Without mounting kit: 1 wire(s)IEC cable at 45 °C, copper 90 °C / XLPE/EPR
    		  
    electrical connection
    Terminal, clamping capacity: 2.5 mm², AWG 14 (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR)
    Terminal, clamping capacity: 50 mm², AWG 1/0 (L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB)
    		  
    tightening torque
    0.6 N.m (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR)
    12 N.m, 102.2 lb.in (L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB)
    		  
    supply
    Internal supply for reference potentiometer (1 to 10 kOhm): 10.5 V DC +/- 5 %, <10 mA, protection type: overload and short-circuit protection
    Internal supply: 24 V DC (21…27 V), <200 mA, protection type: overload and short-circuit protection
    		  
    analogue input number
    2
    		  
    analogue input type
    AI1-/Al1+ bipolar differential voltage: +/- 10 V DC 24 V max, resolution 11 bits + sign
    AI2 software-configurable current: 0...20 mA, impedance: 242 Ohm, resolution 11 bits
    AI2 software-configurable voltage: 0...10 V DC 24 V max, impedance: 30000 Ohm, resolution 11 bits
    		  
    input sampling time
    2 ms +/- 0.5 ms (AI1-/Al1+) - analog input(s)
    2 ms +/- 0.5 ms (Al2) - analog input(s)
    2 ms +/- 0.5 ms (LI1...LI5) - discrete input(s)
    2 ms +/- 0.5 ms (LI6)if configured as logic input - discrete input(s)
    		  
    response time
    <= 100 ms in STO (Safe Torque Off)
    AO1 2 ms, tolerance +/- 0.5 ms for analog output(s)
    R1A, R1B, R1C 7 ms, tolerance +/- 0.5 ms for discrete output(s)
    R2A, R2B 7 ms, tolerance +/- 0.5 ms for discrete output(s)
    		  
    absolute accuracy precision
    +/- 0.6 % (AI1-/Al1+) for a temperature variation 60 °C
    +/- 0.6 % (AI2) for a temperature variation 60 °C
    +/- 1 % (AO1) for a temperature variation 60 °C
    		  
    linearity error
    +/- 0.15 % of maximum value (AI1-/Al1+, AI2)
    +/- 0.2 % (AO1)
    		  
    analogue output number
    1
    		  
    analogue output type
    AO1 software-configurable logic output 10 V 20 mA
    AO1 software-configurable current 0...20 mA, impedance: 500 Ohm, resolution 10 bits
    AO1 software-configurable voltage 0...10 V DC, impedance: 470 Ohm, resolution 10 bits
    		  
    discrete output number
    2
    		  
    discrete output type
    Configurable relay logic: (R1A, R1B, R1C) NO/NC - 100000 cycles
    Configurable relay logic: (R2A, R2B) NO - 100000 cycles
    		  
    minimum switching current
    3 mA at 24 V DC for configurable relay logic
    		  
    maximum switching current
    R1, R2: 2 A at 250 V AC inductive load, cos phi = 0.4
    R1, R2: 2 A at 30 V DC inductive load, cos phi = 0.4
    R1, R2: 5 A at 250 V AC resistive load, cos phi = 1
    R1, R2: 5 A at 30 V DC resistive load, cos phi = 1
    		  
    discrete input number
    7
    		  
    discrete input type
    LI1...LI5: programmable 24 V DC with level 1 PLC, impedance: 3500 Ohm
    LI6: switch-configurable 24 V DC with level 1 PLC, impedance: 3500 Ohm
    LI6: switch-configurable PTC probe 0…6, impedance: 1500 Ohm
    PWR: safety input 24 V DC, impedance: 1500 Ohm conforming to ISO 13849-1 level d
    		  
    discrete input logic
    Negative logic (sink) (LI1...LI5), > 16 V (state 0), < 10 V (state 1)
    Positive logic (source) (LI1...LI5), < 5 V (state 0), > 11 V (state 1)
    Negative logic (sink) (LI6)if configured as logic input, > 16 V (state 0), < 10 V (state 1)
    Positive logic (source) (LI6)if configured as logic input, < 5 V (state 0), > 11 V (state 1)
    		  
    acceleration and deceleration ramps
    Automatic adaptation of ramp if braking capacity exceeded, by using resistor
    Linear adjustable separately from 0.01 to 9000 s
    S, U or customized
    		  
    braking to standstill
    By DC injection
    		  
    protection type
    Against exceeding limit speed: drive
    Against input phase loss: drive
    Break on the control circuit: drive
    Input phase breaks: drive
    Line supply overvoltage: drive
    Line supply undervoltage: drive
    Overcurrent between output phases and earth: drive
    Overheating protection: drive
    Overvoltages on the DC bus: drive
    Short-circuit between motor phases: drive
    Thermal protection: drive
    Motor phase break: motor
    Power removal: motor
    Thermal protection: motor
    		  
    insulation resistance
    > 1 mOhm 500 V DC for 1 minute to earth
    		  
    frequency resolution
    Analog input: 0.024/50 Hz
    Display unit: 0.1 Hz
    		  
    communication port protocol
    CANopen
    Modbus
    		  
    connector type
    1 RJ45 (on front face) for Modbus
    1 RJ45 (on terminal) for Modbus
    Male SUB-D 9 on RJ45 for CANopen
    		  
    physical interface
    2-wire RS 485 for Modbus
    		  
    transmission frame
    RTU for Modbus
    		  
    transmission rate
    4800 bps, 9600 bps, 19200 bps, 38.4 Kbps for Modbus on terminal
    9600 bps, 19200 bps for Modbus on front face
    20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps for CANopen
    		  
    data format
    8 bits, 1 stop, even parity for Modbus on front face
    8 bits, odd even or no configurable parity for Modbus on terminal
    		  
    number of addresses
    1…127 for CANopen
    1…247 for Modbus
    		  
    method of access
    Slave CANopen
    		  
    marking
    CE
    		  
    operating position
    Vertical +/- 10 degree
    		  
    height
    420 mm
    		  
    depth
    236 mm
    		  
    width
    240 mm
    		  
    net weight
    30 kg
    		  
    option card
    Communication card for CC-Link
    Controller inside programmable card
    Communication card for DeviceNet
    Communication card for Ethernet/IP
    Communication card for Fipio
    I/O extension card
    Communication card for Interbus-S
    Interface card for encoder
    Communication card for Modbus Plus
    Communication card for Modbus TCP
    Communication card for Modbus/Uni-Telway
    Overhead crane card
    Communication card for Profibus DP
    Communication card for Profibus DP V1
    		  
    Environment
    noise level
    59.9 dB conforming to 86/188/EEC
    		  
    dielectric strength
    3110 V DC between earth and power terminals
    5345 V DC between control and power terminals
    		  
    electromagnetic compatibility
    1.2/50 µs - 8/20 µs surge immunity test level 3 conforming to IEC 61000-4-5
    Conducted radio-frequency immunity test level 3 conforming to IEC 61000-4-6
    Electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-4
    Electrostatic discharge immunity test level 3 conforming to IEC 61000-4-2
    Radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3
    Voltage dips and interruptions immunity test conforming to IEC 61000-4-11
    		  
    standards
    EN 61800-3 environments 1 category C3
    EN 55011 class A group 2
    EN 61800-3 environments 2 category C3
    EN/IEC 61800-3
    EN/IEC 61800-5-1
    IEC 60721-3-3 class 3C2
    UL Type 1
    		  
    product certifications
    CSA
    NOM 117
    C-Tick
    UL
    GOST
    		  
    pollution degree
    2 conforming to EN/IEC 61800-5-1
    3 conforming to UL 840
    		  
    IP degree of protection
    IP20 on upper part without blanking plate on cover conforming to EN/IEC 60529
    IP20 on upper part without blanking plate on cover conforming to EN/IEC 61800-5-1
    IP21 conforming to EN/IEC 60529
    IP21 conforming to EN/IEC 61800-5-1
    IP41 on upper part conforming to EN/IEC 60529
    IP41 on upper part conforming to EN/IEC 61800-5-1
    IP54 on lower part conforming to EN/IEC 60529
    IP54 on lower part conforming to EN/IEC 61800-5-1
    		  
    vibration resistance
    1 gn (f= 13…200 Hz) conforming to EN/IEC 60068-2-6
    1.5 mm peak to peak (f= 3…13 Hz) conforming to EN/IEC 60068-2-6
    		  
    shock resistance
    15 gn for 11 ms conforming to EN/IEC 60068-2-27
    		  
    relative humidity
    5…95 % without condensation conforming to IEC 60068-2-3
    5…95 % without dripping water conforming to IEC 60068-2-3
    		  
    ambient air temperature for operation
    -10…50 °C (without derating)
    		  
    ambient air temperature for storage
    -25…70 °C
    		  
    operating altitude
    <= 1000 m without derating
    1000...2260 m with current derating 1 % per 100 m
    		  
    Packing Units
    Unit Type of Package 1
    PCE
    		  
    Number of Units in Package 1
    1
    		  
    Package 1 Weight
    36.75 kg
    		  
    Package 1 Height
    24 cm
    		  
    Package 1 width
    40 cm
    		  
    Package 1 Length
    60 cm
    		  
    Offer Sustainability
    Sustainable offer status
    Green Premium product
    		  
    EU RoHS Directive
    Pro-active compliance (Product out of EU RoHS legal scope)
    EU RoHS Declaration
    		  
    Mercury free
    Yes
    		  
    RoHS exemption information  
    China RoHS Regulation  
    Environmental Disclosure  
    Circularity Profile  
    WEEE
    The product must be disposed on European Union markets following specific waste collection and never end up in rubbish bins
    		  
    Contractual warranty
    Warranty
    18 months

  • Reviews ()

    Write a Review